JT&T Products

Users of 3M Super 88 tape will appreciate the value of this premium alternative tape. A 8.5 mil premium vinyl electrical tape. This 20% thicker heavy duty tape allows higher resistance and faster build up. Primary insulation for splices up to 600V, protective outer jacket over splices and for all low temperature applications. Temperature range: -18ºC to 105ºC | 0ºF to 221ºF Made in Spain ...

Heat Shrink Solder Seal terminals feature a band of low melt solder in the middle of heat shrink. They allow you to solder and shrink in one step. Note these terminals do not crimp on and are solder only. If you would like the crimp as well, consider the Crimp & Solder Seal Terminals. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after crimping. JT&T's...

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel.⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

Crimp and Solder Seal terminals feature a band of solder above the connection. After crimping normally, apply heat to activate the heat shrink. The low melt solder will flow into the connection. This provides the best possible connection - no loss of conductivity and is stronger than the wires themselves. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after...

Crimp and Solder Seal terminals feature a band of solder above the connection. After crimping normally, apply heat to activate the heat shrink. The low melt solder will flow into the connection. This provides the best possible connection - no loss of conductivity and is stronger than the wires themselves. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after...

Crimp and Solder Seal terminals feature a band of solder above the connection. After crimping normally, apply heat to activate the heat shrink. The low melt solder will flow into the connection. This provides the best possible connection - no loss of conductivity and is stronger than the wires themselves. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after...

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel.⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

JT&T Products offers a full line of non-insulated & insulated terminals made from vinyl (P.V.C), nylon & heat shrink.

Tapers to a .035" width. Used to release 150 Metri-Pack, 280 Metri-Pack, 280 Tangless, 280 Bus Bar, 630 Pull to Seat, GT 150, GT 280, Wedge Base lamp socket terminals, and Indexing Candelabra Bayonet Double Contact Lamp Socket Terminals. Used to release most GM, Ford & Chrysler OEM terminals from their insulated housing.This tool has the smallest flat blade available. Equivalent to Green Handle Delphi/Packard OEM#12094429 and SPX Kent Moore J-38125-12A Also replaces Delphi/Packard...

Tapers to a .090" width. Used to release larger terminals including Maxi fuse terminals. Also opens secondary locking devices on connector housings. Used to release most GM, Ford & Chrysler OEM terminals from their insulated housing. Can be used as an OEM#12150860 &/or OEM#12094441 tool.

JT&T's 2 to 1 Single/Thin Wall Cross-Linked Polyolefin Heat Shrink Tubing is irradiated, flexible & intended for general purpose applications requiring recognition by military & industrial specifications.  UL recognized, CSA certified, RoHS compliant & ABS approved.  Meets requirements of SAE-AMS-DTL-23053/5 (formerly MIL-I-23053/5, MIL-DTL-23053/5), Classes 1, 2 (Clear), 3. It is single-wall, flame-retardant, mechanically strong &...

This tool is designed for crimping open barrel 18, 16 and 14 gauge terminals found on Weather Packs, Deutsch DT/Amphenol AT stamped terminals, and some Molex type terminals. This tool also performs a starter crimp on 20 thru 12 gauge wire. ? WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

The Weather-Pack Extractor Tool is designed for extracting weather-pack terminals from their connector housing for servicing and replacement. Designed solely to depress Weather Pack terminal retention barbs to allow terminal removal from tower or shroud. Equivalent to: Delphi/Packard OEM#12014012 & SPX Kent Moore J-38125-10A.

JT&T's 2 to 1 Single/Thin Wall Cross-Linked Polyolefin Heat Shrink Tubing is irradiated, flexible & intended for general purpose applications requiring recognition by military & industrial specifications.  UL recognized, CSA certified, RoHS compliant & ABS approved.  Meets requirements of SAE-AMS-DTL-23053/5 (formerly MIL-I-23053/5, MIL-DTL-23053/5), Classes 1, 2 (Clear), 3. It is single-wall, flame-retardant, mechanically strong &...

Heat Shrink Solder Seal terminals feature a band of low melt solder in the middle of heat shrink. They allow you to solder and shrink in one step. Note these terminals do not crimp on and are solder only. If you would like the crimp as well, consider the Crimp & Solder Seal Terminals. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after crimping. JT&T's...

JT&T's 2 to 1 Single/Thin Wall Cross-Linked Polyolefin Heat Shrink Tubing is irradiated, flexible & intended for general purpose applications requiring recognition by military & industrial specifications.  UL recognized, CSA certified, RoHS compliant & ABS approved.  Meets requirements of SAE-AMS-DTL-23053/5 (formerly MIL-I-23053/5, MIL-DTL-23053/5), Classes 1, 2 (Clear), 3. It is single-wall, flame-retardant, mechanically strong & will not melt or split when...

JT&T's 2 to 1 Single/Thin Wall Cross-Linked Polyolefin Heat Shrink Tubing is irradiated, flexible & intended for general purpose applications requiring recognition by military & industrial specifications.  UL recognized, CSA certified, RoHS compliant & ABS approved.  Meets requirements of SAE-AMS-DTL-23053/5 (formerly MIL-I-23053/5, MIL-DTL-23053/5), Classes 1, 2 (Clear), 3. It is single-wall, flame-retardant, mechanically strong &...